Before doing an xtreme garage door opener installation on the gate, you must carefully inspect it to identify defects and also check the smooth movement of the door leaf. It should rise and fall without any braking or hesitation. This point is quite important, since any malfunctions can lead to breakdowns of the garage door openers, which, as a result, can result in significant financial investments in repairs.
Then it is required to calculate the area of the web and determine their mass – this is necessary for the correct calculation of the xtreme garage door opener installation. In order to increase the reliability of the system, it is advisable to purchase a motor with a power 30% higher than the calculated one.
When the automation is purchased, you can start xtreme garage door opener installation. The basis of any type of mechanism is a special control unit. He is responsible for the logic of the device’s functioning and determines its functionality. During xtreme garage door opener installation, the control unit is located in a place where it will be easy to maintain, and all the devices and elements of the mechanism are connected to it.
In some designs, the control unit can be built into the garage door openers, and there is no need to install it separately. After installing the control unit, the motor is mounted on a wall or ceiling, depending on its type. The motor is connected to the lifting mechanism and rigidly fixed. Then it is necessary to supply power, ground all metal elements and perform a test run. The automatic door opener installation process ends with setting up the system.
Xtreme Garage Door Opener Installation – Easy Set Up
Correct xtreme garage door opener installation and competent installation of automation is not the end of the work. The opener requires additional adjustment.
In automatic door opener installation, most often, this process is reduced to adjusting the tension of the cables and the state of the torsion springs.
Emergency situations do not happen suddenly. They are always preceded by seemingly insignificant signs: non-execution of commands from the remote control, partial lowering or incomplete lifting of the canvas, uneven movement, skewed sections, extraneous sounds.
Ed Garage Door Repair’s competent setting of automation allows you to avoid many negative aspects. When conducting an xtreme garage door opener installation, yourself, then adjusting it yourself is also realistic. In principle, the procedure itself is not complicated, but it requires accuracy and adherence to the sequence of actions.
Xtreme Garage Door Opener Installation – Effective Configuration
It is necessary to ensure the tension of the cable with sufficient force before xtreme garage door opener installation, but at the same time it is required to exclude the possibility of breaking. In addition, it is necessary to achieve the same tension of the ropes on both sides of the opener – this is necessary to prevent distortions of the sandwich panels. This can cause deformation of the elements of the canvas, which requires their repair or replacement. Garage doors are available with split and solid shaft – the process of setting them up is slightly different. But in any case, setting up systems begins with a complete relaxation of the traction spring.
During the use of the door, even a slight weakening of the rope tension is unacceptable – this can lead to deformation of the sections and guides. The cable is adjusted as follows:
The lower brackets are firmly fixed to the wall, taking into account the fact that they have to experience significant loads;
A key is mounted on each sandwich panel – the actions must be carried out very carefully so as not to deform the sections;
The required position of the drum is set using the set screw;
The shaft turns extremely slowly until the insufficient tension of the rope is completely eliminated – the action is performed very carefully so that the rope does not over-tension;
To completely guarantee that there is no slack in the xtreme garage door opener installation, the springs are twisted a little, usually in 2-3 turns.
The end of the adjustment – additional fixing of the springs by tightening the bolt heads. In a situation of different tension of the ropes on both sides, the situation can be corrected by simultaneously turning the two parts of the shaft – the design of the connecting coupling makes it possible to do this. To perform the action, it is necessary to release the coupling tie, turn the section on the side of which a weak cable tension is detected. The other section remains stationary. Sometimes it is required to rotate the shafts individually or in one direction. The cable is stretched to the required degree, after the coupling is fixed with bolts.
Setting up a continuous shaft system.
In this case, the procedure is easier. To do this, Ed Garage Door Repair technician removes the panel and find the screw securing the weakened rope. Then he /she slightly loosens the bolt, select the cable, get rid of the excess length and fix it.
The working panel goes back and the rope tension is checked again. If it remains insufficient, the procedure must be repeated. The slack in the cables can cause them to jump off the position, as a result, they become entangled, which will cause the failure of the xtreme garage door opener installation if it is not turned off in time.